|
|
|
Bandmill carriage
This four post band mill carriage can cut up to 29 inches in diameter and requires a minimum nine horse Honda engine. All drawings are included to build this carriage. A small amount of machining is required. The tracks for the carriage to run on are not included in this design however they are very simple to build, you'll need two pieces of angle iron and a straight flat surface to mount them on
This four post band mill carriage can cut up to 29 inches in diameter and requires a minimum nine horse Honda engine. All drawings are included to build this carriage. A small amount of machining is required. The tracks for the carriage to run on are not included in this design however they are very simple to build, you'll need two pieces of angle iron and a straight flat surface to mount them on
Click thumbnails to view fullsize drawings, click here to view complete list of drawings.
$25.95
|
|
|
||||||
|
|
|
Loader plans
Pull behind your pickup and get the logs to your sawmill the easy way. This log loading trailer can self load and unload, all hydraulic design can be powered off your PTO added to your pickup or perhaps an 18 horse engine, plans come with all drawings needed to build this unit including the log grapple the loader and the trailer. The unit has many uses, the loader can be mounted on your own trailer or pickup truck independent of any trailer.
Pull behind your pickup and get the logs to your sawmill the easy way. This log loading trailer can self load and unload, all hydraulic design can be powered off your PTO added to your pickup or perhaps an 18 horse engine, plans come with all drawings needed to build this unit including the log grapple the loader and the trailer. The unit has many uses, the loader can be mounted on your own trailer or pickup truck independent of any trailer.
Click thumbnails to view fullsize drawings, click here to view complete list of drawings.
| ■ | 20 foot reach |
| ■ | Hydraulic grapple rotation |
| ■ | 500 lbs lift @ full reach |
| ■ | 2500 psi pump required |
$42.50
Verticle bandmill
Verticle bandmill design concept, cuts with the blade running verticle, slabs and lumber fall away to the ground, 30 inch cutting capacity.
Verticle bandmill design concept, cuts with the blade running verticle, slabs and lumber fall away to the ground, 30 inch cutting capacity.
|
|
|
Click thumbnails to view fullsize drawings, click here to view complete list of drawings.
$10.95
Outdoor wood boiler plans
These wood boiler plans are for a round firebox design non-pressurized system. The wood boiler can be used to heat your shop or home and domestic hot water. Firebox can except up to 4 foot long logs 16 inches in diameter, this unit is not air injected what can be converted to an air injected model very easily beat the cost of high heating oil prices and get rid of some of your wood waste at the same time
These wood boiler plans are for a round firebox design non-pressurized system. The wood boiler can be used to heat your shop or home and domestic hot water. Firebox can except up to 4 foot long logs 16 inches in diameter, this unit is not air injected what can be converted to an air injected model very easily beat the cost of high heating oil prices and get rid of some of your wood waste at the same time
|
|
|
Click thumbnails to view fullsize drawings, click here to view complete list of drawings.
$25.95
|
|
|
Plasma or oxygen cutting table
Build yourself a table to cut complex patterns in a 4x4 sheet of steel use your plasma cutter or oxygen and acetylene torch to easily trace a pattern and accurately cut it out of steel
Build yourself a table to cut complex patterns in a 4x4 sheet of steel use your plasma cutter or oxygen and acetylene torch to easily trace a pattern and accurately cut it out of steel
Click thumbnails to view fullsize drawings, click here to view complete list of drawings.
$13.99
Bandmill blade repair
Build a bandmill blade repair jig and learn how to repair your broken bandmill blades, step by step instructions with photos on how to weld your blades back together if the are broken
Build a bandmill blade repair jig and learn how to repair your broken bandmill blades, step by step instructions with photos on how to weld your blades back together if the are broken
|
|
|
Click thumbnails to view fullsize drawings, click here to view complete list of drawings.
$13.99
Disclaimer: plans on this site are not certified by an engineer or safety tested. Sawmillplans.com is not responsible for losses or damages as a result of building these projects. Usage of this site is an acknowledgement of this notice.
BUILD AT YOUR OWN RISK
BUILD AT YOUR OWN RISK
Copyright 2008 SAWMILLPLANS.COM All Rights Reserved
Contact: warznorth@yahoo.com with questions or comments.
Website: www.sawmillplans.com www.builditpplans.com
Contact: warznorth@yahoo.com with questions or comments.
Website: www.sawmillplans.com www.builditpplans.com
Loading...
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
